What should operators do before raising the forks or platform of their forklift truck?

Before elevating personnel, mark or cordon off the area with safety cones or other devices to warn others of the work being done. Make sure the lift truck is on a flat, level surface, and has firm, level footing. Make sure the platform is attached securing to the forks or mast as directed by the manufacturer.

What should you do before raising the forks or platform on your lift truck?

Before raising a load, check for enough overhead clearance, and if outdoors, always maintain a safe distance from power lines. Once a load is lifted, the operator must remain on the truck. Additionally—whether or not a lift is loaded—never let anyone walk or stand under an elevated fork.

IT IS IMPORTANT:  What will probably happen when a forklift's center of gravity moves outside the stability triangle?

What should you do before lifting a load forklift?

Lifting the Load

  1. Ensure there is adequate overhead clearance before lifting a load.
  2. Slowly lift a load and tilt the mast backward to stabilize it.
  3. Slowly return the lift control to the neutral position.

When driving a forklift the forks should be at what height?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground.

What must be done first before using a forklift?

The first step toward safe forklift operation is conducting the preoperational inspection. Forklift operators should conduct the inspection at the start of each work shift to ensure that the forklift will work properly. According to OSHA, 1 in 15 forklift-related accidents are caused by improper maintenance.

When should an operator tilt the load back?

The mast must be carefully tilted backward to stabilize the load. Ensure the load is secured before moving. Slowly move the truck to 20 to 30 cm (8 to 12 inches) away from the stack. Stop the truck.

When setting a load What should you do first?

When setting a load, what should you do first?

Place the tasks for lifting a loaf in their proper order.

  1. Level the forks and set the forks for proper width.
  2. Position the load on the forks.
  3. Lift the load straight up.
  4. Tilt the load back slightly.
  5. Back up.

What is the first thing you need to do before raising or lowering a load?

Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.

IT IS IMPORTANT:  Frequent question: What is the legal limit for lifting a truck?

What should you check before lifting a load?

Check out these safe lifting and handling tips, recommended by the Health and Safety Executive.

  1. Think before you lift. …
  2. Keep the load close to the waist. …
  3. Adopt a stable position. …
  4. Ensure a good hold on the load. …
  5. Do not bend your back when lifting. …
  6. Do not bend the back any further while lifting. …
  7. Do not twist when you lift.

How do you adjust forklift forks?

How Do I Make an Adjustment of Width of a Forklift Fork?

  1. Determine the best setting for the forks on your forklift. …
  2. Raise the forks to a height of approximately 30 inches. …
  3. Raise the fork slightly. …
  4. Shift the fork slightly until it drops into the notch nearest the desired distance.

When traveling with empty lift forks The forks should be in what position?

It is a good practice to put the fork arms just below the front axle of the forklift and it should be as close to the ground as possible. When the forks are too low, it could scrape the floor surface.

How often should operators inspect forklift?

An operator should inspect the forklift truck every day, including at the beginning of each shift, and before using each time.

What should be considered when starting forklift operations and planning a task?

16 Simple Tips for operating a forklift safely

  • Operators must be qualified. …
  • Appropriate clothing must be worn. …
  • Examine Equipment before use. …
  • Starting up the forklift. …
  • Consider the surrounding environment. …
  • Operate at a safe speed. …
  • Avoid Hazards. …
  • Ensure your load is stable and secure.
IT IS IMPORTANT:  Is online forklift certification legit?

What is the first thing you should do at the beginning of your shift before operating your pit?

PITs must be inspected at the beginning of each shift to ensure they are safe to operate . These inspections may be performed by authorized PIT operators as long as they are trained on how to properly inspect the PIT .

What are pre operational safety checks on a forklift?

Inspect the tire condition by checking for any balding spots, cracks, cuts, or gouges in tires that need to be addressed. Check the condition of the forks including the top clip retaining pin and heel. Confirm backrest extension is working properly. Ensure all warning decals and plates are in place and legible.